2-1/4 x 1 -5/8″ (6 x 4.5cm)
All-aluminum, precision carriers. Hinged sandwich design for fast handling and loading. Guide pins automatically position negatives in line with carrier aperture. Offset tabs permit rapid opening of carrier. Both glass and glassless models are available. All 4500 Carriers can be used on Omega D5 enlarger (circular film stage opening).
$176.99
Available on backorder
Related Products

$2,731.99Add to cart
JUMBO 160M – 115V
The Bienfang 160M is a high-quality, intermediate-sized press designed for professional dry mounting, laminating and texturing by professional photographers, artists, and educators
The Seal 160M Jumbo press is a table-top, heat-activated dry mounting system that utilizes heat and pressure to mount, laminate and texturize prints on substrates up to 1″ thick. Direct temperature readout for precise control. 115V, 8.3amps, 1000W. Manufacturer’s warranty covers on-site service only.
- Develops 860 lbs. pressure on its large 18.5 x 15.5″ platen
- Free floating platen doesn’t shift
- Extra-wide opening
- Simple pressure adjustments
- Extended temperature range thermostatically controlled from 150-350F degrees
- Non-stick platen
$2,731.99Add to cart

$2,999.00Add to cart
ROSCO LITEPAD AXIOM TUNGSTEN DIGITAL SHOOTERS KIT
ROSCO LITEPAD AXIOM TUNGSTEN DIGITAL SHOOTERS KIT
$2,999.00Add to cart

$1,119.19Add to cart
Model 800 Water Panel
Hot and cold water filtration, & two 20 micron filter cartridges, vacuum breaker, .5-5 GPM flowmeter, adjustable spring check valves, compact design.
$1,119.19Add to cart

$23,127.99Add to cart
VACUUM PRESS 5298H
The Seal 5298H Vacuum Dry Mount Press is another leap forward for the Seal/Bienfang company. As the leading company for photo finishing and mounting, Seal has produced a dry mount press that also pre-dries your board, thereby saving time. This press can handle big jobs and handles multiple pieces at the same time.
Bienfang Vacuum Presses are designed to automatically control the four main variables of mounting: moisture, pressure temperature and time. This assures consistent results. There are two simple ways to operate the Vacuum Press: by setting each control individually or by using convenient programmed settings. Some settings are preset at the factory but you can also set your own programs for procedures you conduct repeatedly.
Platen temperature is maintained at +/- 2° F of the set temperature. Manufacturer’s warranty covers on-site service only.
$23,127.99Add to cart

$2,700.00$2,430.00Add to cart
SCORPRION
The Scorpion rig is the ultimate solution to DSLR shoulder mounted shooting with an EVF. At the center of the Scorpion is our highly adjustable DSLR Baseplate, which allows you to mount any DSLR to the rig and mount your rig onto a tripod. The baseplate attaches to your tripod using the standard tripod plate screws; (2) 1/4 20 and (1) 3/8 16. You can also easily quick release your camera from the rig by turning the red knob on the side of the baseplate and pulling up on your camera. This unique feature allows you to quickly switch between using the camera on its own or as part of your rig.
Our new curved form-fitting silicone gel shoulder pad connects to the back of the baseplate via two 2 M/F rods. The rods screw into the back of the DSLR baseplate and connect to the front of the shoulder pad via 15mm quick release ports, making the switch from shoulder mount to tripod use quick and easy. The Scorpion Shoulder Assembly also features an innovative ball joint built into the front of the shoulder pad. This allows the entire shoulder pad assembly to articulate in multiple directions so shooters can angle it to fit their body for individual comfort. This should be done with one hand while the kit is on your shoulder. The ball joint is released and secured by the red top lever.
The Scorpion can be used on your left or right shoulder. The Scorpion shoulder assembly also has a built in top handle for placing and removing it from your shoulder, low mode shooting and easy carrying. The handle can be positioned up or set down into the shoulder pad for storage with the turn of a Zacuto quick release lever.
The Scorpion kit is finished off with a 7lb Z-lite counterbalance and Zgrips V3 with 4.5 rods. With the shoulder pad and counterbalance weight coming directly off of the back of the baseplate, the rig is perfectly in-line with the camera and ready to be used with one of our EVFs or an on-board monitor for traditional ENG style shooting. You can mount your EVF or monitor to the side of the rig using the included EVF mount.
Scorpion Includes:
-DSLR Baseplate with (2) sets of 3.5″ M/F Rods
-Scorpion Shoulder Assembly
-Zgrips V3 with 4.5″ Rods
-Z-Lite Double
-EVF Scorpion Mount
$2,700.00$2,430.00Add to cart