35mm Full Frame
C700 Negative Carriers are glassless, special spring loaded, rapid shift design with bright top surface and a non-reflective bottom. Stainless steel film guide pins ensure easy film advance, location, and installation.
$156.99
Out of stock
| Weight | 0.5125 lbs |
|---|
Related Products
COMMERCIAL 250 PRESS INTERNATIONAL 230V
The Seal 250 Commercial Dry Mount Press is a table-top, heat-activated dry mounting system. It utilizes uniform heat and pressure to mount, laminate, and texturize prints on substrates up to 1″ thick. It comes with direct temperature readout for precise control. Manufacturer’s warranty covers on-site service only.
Note: This item is ONLY wired for 230V, European voltage.
- Fast Operation
- Superior heating system quickly brings the platen to uniform temperature ensuring 100% bonding.
- Extended Temperature Range
- Thermostat control adjusts from 100-300°F (38-150°C) to cover a wide range of operating temperatures.
- Programmed Heating Cycles
- Temperature and time may be set by stored programs in control unit.
- Temperature Readout
- Platen temperature is indicated on LED display on top of unit.
- Cycle Time Readout
- Remaining time in the cycle is displayed.
- Oversize Capacity
- Design allows processing of materials larger than the press platen by sliding the work side-to-side or out of the front or back of the press.
- Extra-Wide Opening
- Opens a full 9″ (23 cm) for 550 and 10″ (25 cm) for 250 to provide easy access to platen surface
- Easy Pressure Adjustment
- Pressure adjusts and locks in seconds to accept materials up to 1″ (25mm) thick.
- Non-Stick Surface
- Platen surface is specially coated to help keep adhesives from sticking.
- Free-Floating Platen
- Seats evenly on the work without shifting to provide uniform pressure across the entire surface
- Rugged Construction
- Steel cantilevers increase durability and allow maximum pressure on work within the press; metal top and base construction adds ruggedness.
36 X 48 Table 4-40 Watt 5000k Oak Porta-Trace (OVERSIZE)
“The tough stainless steel frame and the thick plexi-glass top team together to provide a durable tool for all your applications for years to come. Features bright, even lighting. “
Model 800 Water Panel
Hot and cold water filtration, & two 20 micron filter cartridges, vacuum breaker, .5-5 GPM flowmeter, adjustable spring check valves, compact design.
VACUUM PRESS 5298H
The Seal 5298H Vacuum Dry Mount Press is another leap forward for the Seal/Bienfang company. As the leading company for photo finishing and mounting, Seal has produced a dry mount press that also pre-dries your board, thereby saving time. This press can handle big jobs and handles multiple pieces at the same time.
Bienfang Vacuum Presses are designed to automatically control the four main variables of mounting: moisture, pressure temperature and time. This assures consistent results. There are two simple ways to operate the Vacuum Press: by setting each control individually or by using convenient programmed settings. Some settings are preset at the factory but you can also set your own programs for procedures you conduct repeatedly.
Platen temperature is maintained at +/- 2° F of the set temperature. Manufacturer’s warranty covers on-site service only.
TRP The Sink II 72″x32″x13″, Black – OVERSIZE (OVERSIZE)
**OVERSIZE**
State-of-the-Art, fully assembled, plumbed, and lab tested. One Year LTD Warranty on Water Controls. plus or minus1/2 degree G, 1-7 GPM Mixer. Check stop valves. Vacuum breaker. Dual scale 3″ thermometer with recalibration screw. 4 Ft. armored spray hose. Includes Thermostatic mixer manual. Stainless steel brackets. Three valves tempered and one untempered water outlets with 3/4″ GHT fittings. 100% plated brass fittings and stainless steel armored 1000 lb. test tubing. 72″ x 32″ x 13″
