RAGMOUNT 48in.x300 ft. ROLL (OVERSIZE)
RagMount is a heat-activated adhesive with a 100% cotton rag tissue carrier. This is the only adhesive on the market today that is designed for dry mounting Giclee prints. It can also be used in dry mounting digital prints to fine art paper and in traditional dry mounting applications.
$839.99
Available on backorder
Related Products
COMMERCIAL 250 PRESS INTERNATIONAL 230V
The Seal 250 Commercial Dry Mount Press is a table-top, heat-activated dry mounting system. It utilizes uniform heat and pressure to mount, laminate, and texturize prints on substrates up to 1″ thick. It comes with direct temperature readout for precise control. Manufacturer’s warranty covers on-site service only.
Note: This item is ONLY wired for 230V, European voltage.
- Fast Operation
- Superior heating system quickly brings the platen to uniform temperature ensuring 100% bonding.
- Extended Temperature Range
- Thermostat control adjusts from 100-300°F (38-150°C) to cover a wide range of operating temperatures.
- Programmed Heating Cycles
- Temperature and time may be set by stored programs in control unit.
- Temperature Readout
- Platen temperature is indicated on LED display on top of unit.
- Cycle Time Readout
- Remaining time in the cycle is displayed.
- Oversize Capacity
- Design allows processing of materials larger than the press platen by sliding the work side-to-side or out of the front or back of the press.
- Extra-Wide Opening
- Opens a full 9″ (23 cm) for 550 and 10″ (25 cm) for 250 to provide easy access to platen surface
- Easy Pressure Adjustment
- Pressure adjusts and locks in seconds to accept materials up to 1″ (25mm) thick.
- Non-Stick Surface
- Platen surface is specially coated to help keep adhesives from sticking.
- Free-Floating Platen
- Seats evenly on the work without shifting to provide uniform pressure across the entire surface
- Rugged Construction
- Steel cantilevers increase durability and allow maximum pressure on work within the press; metal top and base construction adds ruggedness.
670 VCCE Dichroic Auto Variable Contrast
Dichroic Enlarger for All Popular B&W Variable Contrast PapersThe specially designed VCCE system incorporates a unique, dual-range design that provides two separate filtration channels covering all popular variable contrast papers. As filtration is changed, the enlarger automatically introduces the correct amount of neutral density to maintain constant exposure throughout the range of paper grades. This is achieved with state-of-the-art, dichroic cut-off filters which selectively pass certain wavelengths while rejecting others, resulting in a spectrally pure beam of light. The 670VCCE features the same chassis and baseboard as the popular Saunders/LPL 670MXL dichroic and 670CXL triple-condenser enlargers. What's more, the 670VCCE can be purchased as a complete enlarger or lamphouse only, for use on an existing 670-series chassis. Lamphouses are completely interchangeable, without tools. Simply Dial In Filtration – The Enlarger Compensates to Maintain Constant Exposure!The heart of the 670VCCE is its revolutionary lamphouse. Two independent filtration channels allow use of all popular contrast papers: Channel “1” is calibrated for Kodak Polycontrast III, Kodak Polymax and other equivalent variable contrast papers.Channel “2” is calibrated for use with Ilford Multigrade III RC papers, or compatible papers such as Agfa and Oriental.A convenient slide-switch makes channel selection quick and easy. Once the appropriate channel has been chosen, you simply dial in the desired paper grade. Paper grade readout displays are illuminated, stepless and marked in half-grade increments: Channel one displays filtration settings from -1 to 6, Channel Two displays filtration settings from 00 to 5. The unused channel readout is automatically masked to prevent the possibility of error.
SCORPRION
The Scorpion rig is the ultimate solution to DSLR shoulder mounted shooting with an EVF. At the center of the Scorpion is our highly adjustable DSLR Baseplate, which allows you to mount any DSLR to the rig and mount your rig onto a tripod. The baseplate attaches to your tripod using the standard tripod plate screws; (2) 1/4 20 and (1) 3/8 16. You can also easily quick release your camera from the rig by turning the red knob on the side of the baseplate and pulling up on your camera. This unique feature allows you to quickly switch between using the camera on its own or as part of your rig.
Our new curved form-fitting silicone gel shoulder pad connects to the back of the baseplate via two 2 M/F rods. The rods screw into the back of the DSLR baseplate and connect to the front of the shoulder pad via 15mm quick release ports, making the switch from shoulder mount to tripod use quick and easy. The Scorpion Shoulder Assembly also features an innovative ball joint built into the front of the shoulder pad. This allows the entire shoulder pad assembly to articulate in multiple directions so shooters can angle it to fit their body for individual comfort. This should be done with one hand while the kit is on your shoulder. The ball joint is released and secured by the red top lever.
The Scorpion can be used on your left or right shoulder. The Scorpion shoulder assembly also has a built in top handle for placing and removing it from your shoulder, low mode shooting and easy carrying. The handle can be positioned up or set down into the shoulder pad for storage with the turn of a Zacuto quick release lever.
The Scorpion kit is finished off with a 7lb Z-lite counterbalance and Zgrips V3 with 4.5 rods. With the shoulder pad and counterbalance weight coming directly off of the back of the baseplate, the rig is perfectly in-line with the camera and ready to be used with one of our EVFs or an on-board monitor for traditional ENG style shooting. You can mount your EVF or monitor to the side of the rig using the included EVF mount.
Scorpion Includes:
-DSLR Baseplate with (2) sets of 3.5″ M/F Rods
-Scorpion Shoulder Assembly
-Zgrips V3 with 4.5″ Rods
-Z-Lite Double
-EVF Scorpion Mount
