ROSCO LITEPAD AXIOM TUNGSTEN STILL PHOTO KIT
ROSCO LITEPAD AXIOM TUNGSTEN STILL PHOTO KIT
The Seal 210M Dry Mount Press is a table-top, heat-activated dry mounting system. It utilizes uniform heat and pressure to mount, laminate and texturize prints on substrates up to 1″ thick. Comes with a direct temperature readout for precise control. Manufacturer’s warranty covers on-site service only.
|Platen Size||23 x 18.5″ / 58.4 x 47 cm|
|Maximum Thickness||1″ / 2.5 cm|
|Temperature Range||150 to 300°F / 65 to 149°C|
|Dimensions||W: 27 x D: 23 x H: 11 to 20″ / W: 66 x D: 58.4 x H: 27.9 to 50.8 cm|
The Scorpion rig is the ultimate solution to DSLR shoulder mounted shooting with an EVF. At the center of the Scorpion is our highly adjustable DSLR Baseplate, which allows you to mount any DSLR to the rig and mount your rig onto a tripod. The baseplate attaches to your tripod using the standard tripod plate screws; (2) 1/4 20 and (1) 3/8 16. You can also easily quick release your camera from the rig by turning the red knob on the side of the baseplate and pulling up on your camera. This unique feature allows you to quickly switch between using the camera on its own or as part of your rig.
Our new curved form-fitting silicone gel shoulder pad connects to the back of the baseplate via two 2 M/F rods. The rods screw into the back of the DSLR baseplate and connect to the front of the shoulder pad via 15mm quick release ports, making the switch from shoulder mount to tripod use quick and easy. The Scorpion Shoulder Assembly also features an innovative ball joint built into the front of the shoulder pad. This allows the entire shoulder pad assembly to articulate in multiple directions so shooters can angle it to fit their body for individual comfort. This should be done with one hand while the kit is on your shoulder. The ball joint is released and secured by the red top lever.
The Scorpion can be used on your left or right shoulder. The Scorpion shoulder assembly also has a built in top handle for placing and removing it from your shoulder, low mode shooting and easy carrying. The handle can be positioned up or set down into the shoulder pad for storage with the turn of a Zacuto quick release lever.
The Scorpion kit is finished off with a 7lb Z-lite counterbalance and Zgrips V3 with 4.5 rods. With the shoulder pad and counterbalance weight coming directly off of the back of the baseplate, the rig is perfectly in-line with the camera and ready to be used with one of our EVFs or an on-board monitor for traditional ENG style shooting. You can mount your EVF or monitor to the side of the rig using the included EVF mount.
-DSLR Baseplate with (2) sets of 3.5″ M/F Rods
-Scorpion Shoulder Assembly
-Zgrips V3 with 4.5″ Rods
-EVF Scorpion Mount
The Seal 5298H Vacuum Dry Mount Press is another leap forward for the Seal/Bienfang company. As the leading company for photo finishing and mounting, Seal has produced a dry mount press that also pre-dries your board, thereby saving time. This press can handle big jobs and handles multiple pieces at the same time.
Bienfang Vacuum Presses are designed to automatically control the four main variables of mounting: moisture, pressure temperature and time. This assures consistent results. There are two simple ways to operate the Vacuum Press: by setting each control individually or by using convenient programmed settings. Some settings are preset at the factory but you can also set your own programs for procedures you conduct repeatedly.
Platen temperature is maintained at +/- 2° F of the set temperature. Manufacturer’s warranty covers on-site service only.
The KSE-250i is the newest film cleaner from Kinetronics. The KSE-250i is designed to clean up to 10″ or 250mm wide. The KSE-250i has electronic ionization, four anti-static brushes and filtered air. The high-tech cleaner has six titanium emitters to create clouds of ions that dissipate static charges on film. Dust and debris are then smoothly whisked off the film, which insures crisp, sharp images and scans.
The KSE-250i is designed for use by digital labs, aerial photographers and fine art photographers. It has been engineered to be a tough “work horse” with a steel cabinet, state of the art low-voltage circuit design and a ball bearing fan. The machine operates on 12 volts DC and uses a universal power supply with input from 90 VAC to 240 VAC in either 50 or 60 Hz. For correct power cord please specify the country of use. The KSE-250i is sold with a one-year warranty.
LENGTH: 14″ or 356mm
WIDTH: 4 1/4″ or 105mm
HEIGHT: 4 1/2″ or 114mm
WEIGHT: 5.3 lbs or 2.4 kg.
SHIPPING WEIGHT: 6 lbs. or 2.75 kg.
The Bienfang Masterpiece 250 & 550 Mechanical Press are versatile, dependable and will handle an array of sizes and artistic applications. Both the 250 & 550 models have an easy to read digital display with touch pad controls and pre-set programs.
- Heat Mounting
- Applying Texture
- All have capability of finishing pieces larger than press itself
- Adjustable pressure for materials up to 1″ thick
- Easy to clean platen surfaces